PCB Manufacturing Process

  • 14.08.2019
  • admin
  • PCB Manufacturing Process

 PCB Making Process

Generally, PCB are made of copper plated on a substrate. The excess copper is etched away to expose the circuits. As technology progresses, multiple layers of the circuit boards are bonded together and connected through vias hole.

Steps of PCB Manufacturing

1. PCB Design

2. Printing the Design

3. Creating the Substrate

4. Printing the Inner Layers

5. Ultraviolet Light

6. Removing Unwanted Copper

7. Inspection

8. Laminating the Layers

9. Pressing the Layers Step

10. Drilling

11. Plating

12. Outer Layer Imaging

13. Plating

14. Etching

15. Solder Mask Application

16. Silkscreening

17. Surface Finish

18. Testing

Step 1 – The Design

Before you begin manufacturing the PCB, you need to have a design of the board. These blueprints will be what you base the process off of. The design process is generally completed through computer software. Using a trace width calculator will help with a majority of the details needed for inner and external layers.

Step 2 – Printing the Design

A special printer called a plotted printer is used to print the design of the PCB. It produces a film that shows the details and layers of the board. When printed, there will be two ink colors used on the inside layer of the board:

·         Clear Ink to show the non-conductive areas; and

·         Black Ink to show the conductive copper traces and circuits.

The same colors are used for the outer layers, but the meaning of them is reversed.

Step 3 – Creating the Substrate

Now is when the PCB will start to form. The substrate, which is the insulating material (epoxy resin and glass fiber) that holds the components on the structure, begins forming by passing the materials through an oven to be semicured. Copper is pre-bonded to both sides of the layer and then etched away to show the design from the printed films.

Step 4 – Printing the Inner Layers

The design is printed to a laminate, the body of the structure. A photo-sensitive film made from photo-reactive chemicals that will harden when exposed to ultraviolet light (the resist) covers the structure.. This will help align the blueprints and the actual print of the board. Holes are drilled into the PCB to help with the alignment process.

Step 5 – Ultraviolet Light

Once aligned, the resist and laminate go under ultraviolet lights to harden the photoresist. The light reveals the pathways of copper. The black ink from before prevents hardening in areas that will be removed later on. The board is then washed in an alkaline solution to remove the excess photoresist.

Step 6 – Removing Unwanted Copper

Now, it is time to remove any unwanted copper that remained on the board. A chemical solution, similar to the alkaline solution, eats away at the unwanted copper. The hardened photoresist remains intact.

Step 7 – Inspection

The newly-cleaned layers will need to be inspected for alignment. The holes drilled earlier help align the inner and outer layers. An optical punch machine drills a pin through the holes to keep the layers lined up. After the optical punch, another machine will inspect the board to ensure there are no defects. From here on out, you will not be able to correct any missed errors.

Step 8 – Laminating the Layers

Now, you will see the board take shape as the layers are fused together. Metal clamps hold the layers together as the laminating process begins. A prepreg (epoxy resin) layer goes on the alignment basin. Then, a layer of substrate goes over the prepreg followed by a copper foil layer and more prepreg resin. Lastly, there is on more copper layer applied, which is the press plate.

Step 9 – Pressing the Layers

A mechanical press is then used to press the layers together. Pins are punch through the layers to keep them properly aligned and secured, these pins can be removed depending on the technology. If correct, the PCB will go to the laminating press, which applies heat and pressure to the layers. The epoxy melts inside of the prepreg that, along with the pressure, fuses the layers together.

Step 10 – Drilling

Holes are drilled into the layers by a computer-guided drill to expose the substrate and inner panels. Any remaining copper after this step is removed.

Step 11 – Plating

The board is now ready to be plated. A chemical solution fuses all of the layers together. The board is then thoroughly cleaned by another series of chemicals. These chemicals also coat the panel with a thin copper layer, which will seep into the drilled holes.

Step 12 – Outer Layer Imaging

Next, a layer of photoresist, similar to Step 3, is applied to the outside layer before being sent for imaging. Ultraviolet light hardens the photoresist. Any undesired photoresist is removed.

Step 13 – Plating

Just like in Step 11, the panel is plated with a thin copper layer. After this, a thin tin guard is layered to the board. The tin is there to protect the copper of the outside layer from being etched off.

Step 14 – Etching

The same chemical solution from before removes any unwanted copper under the resist layer. The tin guard layer protects the needed copper. This step established the PCB’s connections.

Step 15 – Solder Mask Application

All of the panels should be cleaned before the solder mask is applied. An epoxy is applied with the solder mask film. The solder mask applies the green color you typically see on a PCB. Any unwanted solder mask is removed with ultraviolet light, while the wanted solder mask is baked on to the board.

Step 16 – Silkscreening

Silkscreening is a vital step since this process is what prints critical information onto the board. Once applied, the PCB passes through one last coating and curing process.

Step 17 – Surface Finish

The PCB is plated with either a solderable finish, depending on the requirements, which will increase the quality/bond of the solder.

Step 18 – Testing

Before the PCB is considered complete, a technician will perform an electrical test on the board. This will confirm the PCB functions and follows the original blueprint designs.

 

Tags: PCB Making, PCB Manufacturing